Home > FAQ > Chkdsk taking days - how to decide

Chkdsk taking days - how to decide

How long will a chkdsk take to run?

5 hours

Storage is a very important part of fault tolerance. If something happens to a company's data, such as For example, if a hard drive failure leads to data loss, it can have a serious impact on business performance. That is why we need to make sure that if a hard drive fails so that no data loss would occur.

And one of the best ways to prevent data loss is through RAID. RAID stands for redundant array of independent hard drives. With a RAID setup, the data is copied to multiple hard drives.

So that no data is lost in the event of a hard drive failure. Now there are four common types of RAID. There are RAID 0, RAID 1, RAID 5, and RAID 10.

RAID 0 is now not fault tolerant. In fact, RAID 0 shouldn't even be called RAID because not only does it not provide fault tolerance, but it actually increases the likelihood of data loss. Because in a RAID 0 the data is not duplicated, but actually distributed on two separate hard drives, so only one of these hard drives has failed, or if you decide to destroy yourself with a hammer, all data will be lost.

The only reason you'd want to use RAID 0 is for speed. Because if you have 2 hard disk controllers working instead of 1, then data access is much faster. RAID 1 is now fault tolerant.

With a RAID 1 setup, the data is copied to more than one hard drive. Hard disk 2 has exactly the same copy of the data as hard disk 1. In the event of a single hard disk failure, e.g.

B. if it is destroyed by a laser beam, there would be no data loss because the other hard drive would have a duplicate copy. I'll talk about RAID 5.

To use RAID 5, you need 3 or more hard drives. RAID 5 is probably the most common setup because it is fast and can store a large amount of data. In a RAID 5 setup, the data is not duplicated, but rather striped or distributed over several hard drives.

And in addition to the data, there is another very important piece of information that is evenly distributed across all hard drives and this information is called parity, and parity is used to restore the data in the event of a hard drive failure. But RAID 5 also has a disadvantage, because since it uses the equivalent of an entire hard drive to store parity, it reduces the collective amount of data that can be stored in that array. So, for example, if all 4 of these hard drives are each 1 terabyte, that's 4 terabytes, but in a RAID 5 setup, the total amount used for data storage would be 3 terabytes, as the equivalent of an entire hard drive to store the Parity would be used.

And finally there is RAID 10 and RAID 10 is basically what the name says, it combines RAID 1 and RAID 0 together and you have to use at least 4 hard drives. In a RAID 10 setup, a set of 2 hard drives is mirrored with a RAID 1 setup. Then both sets of the two hard drives are stripped with RAID 0.

phantom mouse clicks

For example, RAID 10 benefits from the fault tolerance of RAID 1 and the speed of RAID 0. The disadvantage of RAID 10, however, is that you can only use 50% of the capacity for data storage. So if you are using four hard drives in a RAID 10 setup, you can only use two of them for actual storage.

How can I speed up chkdsk?

The chkdsk process is usually completed in 5 hours for 1TB drives, and if you're scanning a 3TB drive, the required time triples. As we already mentioned, chkdsk scan can take a while depending on the size of the selected partition.

It happens to everyone. You buy a brand new computer and when you start it up for the first time you are amazed at how fast it is. But then ... go by a few years or even months, and before you know it, the computer is struggling to even run basic programs.

What happened? Well, there are many reasons a computer can slow down over time, but I've bought a list of ten things you can do in Windows to hopefully make it run more like the first time around. And don't worry, these are all simple and free things you can do right now. Some of these may seem obvious, but others may not.

So, let's go. First and foremost, clean out your startup programs AND services; this must be the main reason behind the slowdown over time, because think about it. As time goes on and you install new programs, many of them start with windows.

And if you don't close them, more and more programs will be running in the background, consuming resources. But don't think that's just because you don't see a lot of programs in the system tray, not a lot of programs running in the background. In Windows 8 and 10, you can open Task Manager by pressing Ctrl + Shift + Esc and going to the Start tab to see ALL programs that start with Windows.

On Windows 7 and earlier, go to the start menu and run 'msconfig'. Right click and disable any programs you don't need right away. Of course, you can always run them manually, but they don't need to be started.

This is where most of the people screw up. Because the start tab isn't the end of the story. Because many programs install what are called 'services' which are still programs that run in the background but you never see them.

So number two is to go through these startup services and disable any unneeded services. You can do this by going to the start menu and running 'Services.msc' you will get a list of all the services, and any that say 'automatically' will start Windows right click on them and change the startup type to 'manual', so that they only run when the program starts.

Remember that you should be more careful about disabling these programs, especially programs that you do not necessarily run manually - for example, disabling the printer service the next time you print can cause problems, so only disable services from those They know you don't have to run them in the background, which is also great for programs that keep starting, but you can't find it in the startup list. It is, in fact, probably a service. Now quick, as a number '2.5' so to speak, which is pretty reasonable and goes one and two, but uninstall any unused programs on disk space and remove startup junk without going through the entire list of startup programs and services to get around find out what each one is doing.

Okay number three, another simple task that hopefully you're already doing is scanning for malware and viruses Your computer is always running.If it's slow for no apparent reason, it is possible that malicious software hidden in the background is running from the display from advertising to using your computer resources in a botnet. Now there are both free and paid antivirus options, and free versions of paid ones.

These include Avast, AVG, Bitdefender, and Malwarebytes. For paid programs, I personally use Eset Smart Security and I am satisfied with it. Even if your computer isn't running slowly, you should have some kind of antivirus on your computer, for reasons I've covered in many other articles.

Ok, number four is quick and easy, and that disables Windows animations. One way to do this is to go to the Ease of Access Settings window and tick the box. If possible, turn off any unnecessary animations.

You can also choose Control Panel> System> Advanced System Settings> Performance Settings and customize the animations to use. You can choose the best performance, which disables all, or choose and choose. This will likely make the biggest difference on low power computers.

Next, you need to keep all of your software up to date. This includes Windows itself, your graphics drivers, and anything else you use on a regular basis. They often release new updates that optimize performance. , as well as improving security.

Also, it's just good practice. Number six. Check your power settings! Especially on laptops, the default setting may be set to 'Balanced' or even 'Power Save' which is good for power saving. but it will also slow down your computer significantly.

Instead, you might want to change it to high performance, definitely when you're on a desktop and maybe only on a laptop when you're plugged in. I learned this the hard way a couple of years ago I got a brand new laptop that was really meant to be high end. But when I got it, it was SO slow, I couldn't figure out why.

After a few days I finally realized it was in low power mode, and when I switched to high performance, THEN it was lightning fast. So be sure to check that out. Okay, we're getting a little more technical now, but don't worry So number seven is to check your hard drive for errors, there are several ways you can do it.

Firstly, you can check the reported health of the hard drive by going to the command prompt, so from the start menu, typing CMD. Then type in 'WMIC' and then 'diskdrive get status'. If they all say OK, one for each hard drive, it means that there aren't any immediate fatal errors that it at least thinks about.

If it says anything other than OK then one of your drives may be having problems and you should REPLACE it. The other way to check for drive errors is to go to the command prompt and run the CheckDisk command by typing 'CHKDSK / f' which will look for errors on your drive and try to fix errors. In turn, if you keep getting a lot of errors, it could mean your drive is failing.

This is why you always want to make a backup. ALWAYS! Number eight. Check Windows file integrity.

At the good ol 'command prompt, type' SFC / scannow 'to get t. Run System File Checker tries to find any system files that are missing or damaged and tries to repair them. Now there are a lot of opportunities for error messages he might spit out for you.

So when you get one you'll just have to googling it yourself ok? I'm not going to help everyone with every random bug they get because I wouldn't know what they are without looking them up too. Go to number nine. Check for Memory Errors Memory, it can cause ALL kinds of weird problems that you might never have suspected were related to your RAM.

To do this, go to the start menu and look for 'Windows Memory Diagnostic'. Now, careful, don't hit 'restart now' unless you actually want to restart this second. You'd probably prefer to look the next time you start up and restart whenever you want.

After rebooting, it should just start automatically and let you know if something happens. Or if you want to continue you can use 'F1' to change the test settings, but that's not really necessary.If you're getting a lot of errors, it could mean that your RAM is not sitting properly or one of the sticks is defective and needs to be replaced .

If the RAM is indeed bad, swapping is really the only option, although there are a couple of non-free things I'll mention in a moment. So number ten is to just destroy it and start over. Reformat the hard drive and reinstall Windows from scratch.

This is obviously the most extreme option, but when you're constantly having problems that you can't seem to fix, reinstalling Windows is often the best way to go. Explaining how to reformat and reinstall Windows is beyond the scope of this article, and if you have no idea what I'm talking about then it is probably NOT something you should be doing. But this list would not be complete without them.

Next up are a couple of bonus options, but these actually involve purchasing new hardware, so they're not free. First, you can buy an SSD to replace your main hard drive small and just boot Windows from it, but SSDs are much cheaper today to get a big one. Let me just tell you that there is probably nothing that will make your computer run faster than an SSD 'not ancient, and if you have one you will never want to go back.

calibrate laptop touchpad

The other thing you can do is MAYBE buy more memory depending on how much you have now. If you have 8GB of RAM or less, and you don't just check your email and type in Word documents, you could probably benefit from getting more. I definitely think getting an SSD first would be much more beneficial though, so I think that sums it all up, these should be some great things to try if your computer is running slower than it should be.

If I've forgotten something, please let me know, so maybe leave a comment with any tips you think are helpful too. And if you liked the article, give it a thumbs up. If you want to look further, I have a few other articles here, you can click on them even if you are on the phone.

And if you want to subscribe, I make new articles every Tuesday, Thursday Saturday, also consider clicking the bell next to the subscribe button to receive notifications as YouTube's algorithm will probably not show you my new articles. So again I look forward to hearing from you so thanks for watching, I'll see you next time, enjoy yourself.

Is it safe to shut down during chkdsk?

If you want to speed up the scanning, the only way is to mirror/backup your whole partition (e.g. Partition Magic or Norton Ghost) and scan it on more healthy drive. It won't speed up the check for bad sectors, which has to hit the entire drive anyway. I recommend running chkdsk overnight on the drive as it is.

Twelve Signs That Your Computer Has Been Hacked. Cyber ​​attacks have become a very popular problem recently, so everyone is concerned about keeping their data safe. To prevent your passwords or other important data from being stolen, you need to be on look out for any changes on your computer; your printer is not working properly and you do not know what it means.

Your webcam is behaving abnormally. We'll tell you about 12 key signs that your computer has been hacked and your data and pictures have been stolen. Number twelve - the antivirus is off.

Antivirus programs are pretty hard to turn off, even if you have special security protocols asking you two or even three times if you are sure the program is not working. So it's almost impossible for you to accidentally turn it off. The first thing good hackers do is turn off the antivirus so you can't detect the intrusion.

But you're smarter than them, right ??? As soon as you notice your antivirus is disabled, turn it back on and contact a specialist. Number eleven - you are getting fake antivirus warnings, if you see antivirus warnings that look different or unusual, this is a clear sign of a hack. Another bad sign is when you haven't installed a new antivirus program.

Before you worry though, make sure that your old antivirus software has been updated. Maybe it just looks different now. Number ten - your passwords aren't working.

If you can't access some of your accounts and are sure you haven't changed and forgotten your passwords, most likely your computer has been hacked. Fortunately, most services have two-factor authentication so you can recover your passwords by Get a code sent to your phone number. When you've done this, change the passwords for those accounts that don't seem to have been hacked yet.

Tell all your friends not to open any messages from you and those sent from your accounts Links not to use. Number nine - your number of friends has grown. If you see some people on your social networking pages that you don't know, and there are many of them, it is a clear sign that your computer, or at least your account, is was hacked.

Check chats with your friends for spam messages. Number eight - new icons appear on your dashboard browser and notice new icons on your dashboard, this could be a sign that dangerous code is infiltrating your computer. Do not run unknown applications unless you want to make the hackers' job easier.

Try to delete them from your computer if you can. Number seven - the cursor moves on its own. If you notice that your cursor is moving without your control and highlighting something, it means that your computer has definitely been hacked, something at that moment.

What you should do is turn off the internet connection as soon as possible. Of course, after you've finished watching this article and liking it. This means disconnecting the ethernet cable or turning off your WiFi router until a specialist arrives and fixes the problem.

Number six - your printer is not working properly. You might be surprised, but cyberattacks affect not only the computer itself, but also your peripherals. For example, if your printer refuses to print, this can be a worrying signal.

Or you just run out of paper. Who knows? The same goes for any other device connected to your computer. Number five - you will be redirected to different websites.

You should be vigilant if your browser is constantly redirecting to other websites. Maybe it's your own fault. Do you remember visiting some suspicious looking websites? If not, your system may have been hacked.

It's time to call a specialist when you type something into a search engine and instead of Google Pages you go to another page that you don't know. The same goes for situations where you see too many pop-up windows. Number four - your files are being deleted by someone else.

This is a 100% mark of a hack. If you find that your folders are empty, don't panic. There are a few tools out there that can recover deleted files, so this is not the most pressing issue.

But your system is secure. Number three - your data is on the internet, although you haven't put it there, you have probably heard a lot of stories in the news about celebrities whose photos have been stolen and shared with the whole world. This is a terrible situation and it can happen to anyone.

It's just that only celebrity stories end up in the newspapers. Hackers can blackmail you and threaten to share your information with your friends. YOUR NEXT Take care of your credit cards first.

Call your bank and tell them to block the cards you used to pay online. Only when your money is safe do you call a specialist who can look into the security problem. The stolen data cannot be returned, so everything online stays online.

Try not to save files that are not intended to be stolen from your computer. Number two - there is unusual webcam behavior. Check your webcam- Display.

If it is on or flashing, make sure not to launch any applications that require a webcam like Skype, FaceTime, or others. If you don't see any reason to turn on the webcam, restart the system and check again. If the indicator lights up again, there is a problem.

Disconnect from the internet and call a specialist. Number One - Your Computer Is Working Very Well If your computer is taking a long time to complete even the simplest of operations and you are experiencing a significant drop in the speed of your Internet connection, it could mean that someone has hacked your computer. First, try restarting your computer and checking the performance again.

Maybe you just need a hardware upgrade. If nothing changes, start Task Manager and look for the processes that are taking up your memory. Shut down any tasks you can and see how well the computer works.

If you run into trouble after that, you already know what to disconnect and who to call. WHAT YOU SHOULD DO So let's summarize and repeat what you should do. Warn your friends and others you've emailed that your computer has been hacked by clicking any link from you.

background transfer host

Inform your bank about a possible loss of your data. Find out how to protect your money. Delete all unknown programs and even those that you cannot start.

Install a reliable antivirus and scan your system. Some companies make trial versions. Change the passwords for all of your accounts.

If you still feel that the problem is not resolved, contact a specialist. Hit the 'Like' button if you think cybersecurity is very important these days. Share it with your friends who have devices with internet access.

So share it with everyone and click Subscribe to join us on the bright side of life.

Which stage of chkdsk takes the longest?

2 Answers. You will not damage the computer or the hard drive by restarting it during a CHKDSK if it's locked up (during so while it's actively working isn't advised though, as you could cut power while the drive is in the middle of relocating data from bad sectors).

What does it mean to defrag your hard drive? Defragmentation now reduces the amount of fragmented files on your hard drive. It rearranges related data files and places them in the same physical location on your hard drive. For example, if you install data on your hard drive; B. programs, documents, music, articles, etc., this data is actually broken down into several data blocks that are stored on the hard drive.

So after a while, your hard drive will look something like this. All of your data is distributed and mixed with other data files. So when you perform a defragmentation, the defragmentation will reassemble any related blocks of data that were broken up and put them together in the same physical location.

So it merges all the files that belong to a certain program, all the files that belong to a certain article, the same goes for documents, music, etc. It also merges all of the free space on the hard drive. And after the defragmentation is complete, the files on your hard drive will look something like where all of the related files are together and everything is nice and organized.

Another example: Let's install a program on this empty hard drive and make sure during the installation that the files for this program are close together and not scattered in different places, but rather close together. Now let's install another program and install another program. As you can now see, the data files of each of these programs were installed in close proximity to each other on the hard drive.

This means that if you try to run any of these programs, the computer will run faster because the hard drive won't. You don't have to do any extra work by pulling data from different areas of the hard drive. Now, as data is added and deleted, the free space on the hard drive will shrink over time and be spread across different locations on the hard drive rather than in one general location.

As you can see, the free space on this hard drive is divided into different blocks. So if another program is installed, the computer may not be able to find enough free space in one place on the hard drive to house the program because the free space is scattered in different places. For example, if we install another program on that hard drive and the computer cannot find enough free space for that program in an area, the computer will spread the program's data files in smaller blocks across the hard drive.

So it could be 50 miles here, 30 miles there, and 20 miles elsewhere. And when you have related files that are scattered in different places on the hard drive, this is called fragmentation. When you have a fragmented hard drive, the computer slows down because the computer has to work harder to read and write data. because the data is scattered all over the hard drive.

In this case, you need to perform a defragmentation. During a defragmentation, all of the related files that are scattered around the hard drive are collected and combined so that they are in the same physical location on the hard drive. And it does its best to pack the free space into one big chunk, too.

And after the defragmentation is complete, your computer will run faster and more efficiently. As you can see in this before and after graph, all of the associated data files are together and all of the free space is put together. Now all you need to do is defragment mechanical hard drives because mechanical hard drives have hard drives that spin so heads can read and write data files.

No defragmentation is now required for solid-state drives or SSDs. Because SSDs have no moving parts. The computer can simply select any file it needs, regardless of what memory chip the file is on.

How long does it take to run CHKDSK / F / are / X?

chkdsk -f should take under an hour on that hard drive. chkdsk -r will take some time. It could take over an hour, maybe two, three, or more, depending on your partitioning. You can interrupt the scan, but not recommended.

How long does it take to do CHKDSK in Windows 10?

It is nearly impossible to figure out exactly how long does CHKDSK take in Windows 10 to complete. The process depends mainly on the following things, For a system with the 1TB hard disk, the CHKDSK can take up to 5 hours and with the increase in the size of the hard drive, the time also took hikes.

Why is my CHKDSK drive taking so long?

Using the Hitachi drive test, the drive came back all clear from both the quick and advanced tests. 1. Why is chkdsk taking so long? I have never had to wait more than maybe 8 hours for one to complete on a larger drive. 2. The drive doesn't seem to be faulty as the drive test came back all clear.

What do I need to know about CHKDSK command?

What Is CHKDSK Command. CHKDSK, also known as Microsoft Check Disk, is a utility that can be used in almost all Windows versions. The CHKDSK command is used to scan through your entire hard drive to find and fix any errors.

Other Questions In This Category

Video.ui.exe windows 10 - simple answers to questions

What happened to Windows Photo Gallery? Note: Do not forget that Windows Photo Gallery has been discontinued and Microsoft no longer offers support for it. If you have any issues with the app, you'll have to solve them on your own.

Searchindexer.exe windows 10 - solutions to the problems

How do I uninstall and reinstall my firewall? How to Reinstall Windows Defender Firewall in Windows 10Step 1 – To Reinstall Windows Defender Firewall, open Start Menu, and type cmd. Step 2 – This action will launch UAC prompt on your PC screen, select Yes.Recreate the Service. Start Windows Defender Firewall Service. Reset Windows Defender Firewall Configurations.

Windows upgrade 9252 - how to decide

Can you install Windows 8.1 without a key? The fastest and easiest way to install Windows 8.1 without a product key is by creating a Windows installation USB drive. We need to download a Windows 8.1 ISO from Microsoft if we haven't already. Then, we can use a 4GB or larger USB flash drive and an app, such as Rufus, to create a Windows 8.1 installation USB.12 mei 2017